Industrial CFD simulation
Industrial CFD simulation

Flow velocities and distribution analysed with CFD

An installation may move sufficient air, water or gas and yet not function correctly. The cause often lies in the local velocity distribution. In some places the medium flows too fast, while elsewhere stagnant zones, recirculation or insufficient flow occurs.

With CFD, we visualise the entire flow in three dimensions. This reveals where high velocities, vortices, dead zones and uneven distributions arise. Subsequently, we investigate together what adjustments are necessary to better control the flow.

Industrial CFD simulation

Flow velocities and distribution analysed with CFD

An installation may move sufficient air, water or gas and yet not function correctly. The cause often lies in the local velocity distribution. In some places the medium flows too fast, while elsewhere stagnant zones, recirculation or insufficient flow occurs.

With CFD, we visualise the entire flow in three dimensions. This reveals where high velocities, vortices, dead zones and uneven distributions arise. Subsequently, we investigate together what adjustments are necessary to better control the flow.

Typical problems

Typical problems

Typical problems

  • Unexpectedly high velocities occur in certain locations.

  • The flow is not evenly distributed across the installation.

  • There are zones in which barely any movement or ventilation takes place.

  • Products, components or workstations are subjected to uneven flow.

  • A ventilation or extraction system does not achieve the desired capacity everywhere.

  • The flow causes draughts, noise, vibrations or extra wear.

  • The measured volumetric flow is correct, but the process still performs poorly.

  • Bends, valves, grilles or restrictions disturb the flow.

  • The flow chooses a different route than was expected during design.

  • Adjustments to the installation do not produce the desired effect.

What we investigate

What we investigate

What we investigate

  • Local flow velocities and flow directions.

  • Insight into the entire flow

  • Distribution of the flow rate across ducts, branches or openings

  • High-velocity zones at restrictions, grilles and inlets

  • Stagnant zones and areas with insufficient ventilation

  • Vortices, recirculation and backflow

  • Pressure differences and pressure losses

  • Turbulence and mixing

  • Outlet profiles from nozzles, grilles or fans

  • Flow around obstacles, products and structures

  • Residence time and through-flow of different areas

The results can be displayed with velocity contours, vectors, streamlines, cross-sections and animations. This makes it quickly clear where the problem arises.

Potential improvements

Potential improvements

Potential improvements

  • Adjusting inlet or outlet positions

  • Increasing or decreasing flow openings

  • Changing duct diameters and cross-sections

  • Improving bends, transitions and branches

  • Adding guide vanes, distribution plates or flow straighteners

  • Adjusting grilles, nozzles or perforation patterns

  • Reducing abrupt contractions and expansions

  • Relocating or adjusting fans

  • Reducing recirculation and dead zones

  • Distributing the available flow rate more evenly

Different design variants can be compared digitally before an installation is modified or built.

Applications

Applications

Applications

  • Ventilation and extraction systems

  • Air ducts and piping networks

  • Process installations

  • Industrial ovens and dryers

  • Cooling installations and heat exchangers

  • Cleanrooms and production areas

  • Tanks, vessels and mixing installations

  • Chimneys and flue gas ducts

  • Filters, cyclones and separators

  • Nozzles, grilles and diffusers

  • Electronic housings and battery systems

  • Storage rooms and technical buildings

  • Flow around machines, vehicles and structures

CFD can be applied both to an existing problem and during the development of a new design.

Our approach

Our approach

Our approach

  1. We discuss the installation, measurements and desired performance.

  2. We determine which geometry and physical processes are required in the CFD model.

  3. We simulate the existing situation and visualise the flow.

  4. We compare the results where possible with measurements or practical observations.

  5. We determine the cause of the unwanted velocity distribution.

  6. We investigate one or more possible improvements.

  7. We translate the results into clear and actionable recommendations.

The goal is not just an attractive flow image, but primarily insight with which a technical decision can be taken.

Why FlowMotion

Why FlowMotion

Why FlowMotion

  • To make the cause of a flow problem visible

  • Experience with complex industrial flows

  • To compare design variants objectively with each other

  • To avoid unnecessary adjustments and costly practical tests

  • To reduce risks before production or commissioning

  • To take evidence-based design decisions

Would you like to understand flow velocities and distribution in your system?

Tell us about your system, its operating conditions and the problems you have observed. We will discuss how CFD can identify the causes and assess practical improvements.