CFD visualisation of airflow and temperature distribution around hot parts in an industrial system.
CFD visualisation of airflow and temperature distribution around hot parts in an industrial system.

Cooling and heat transfer analysed with CFD

Overheating, uneven cooling and unnecessary energy loss often occur because air or fluid does not flow as expected. With CFD, we combine flow and heat transfer in a single analysis. This allows us to visualise where heat originates, how it is dissipated and which parts of a system are insufficiently or unnecessarily strongly cooled.

CFD visualisation of airflow and temperature distribution around hot parts in an industrial system.

Cooling and heat transfer analysed with CFD

Overheating, uneven cooling and unnecessary energy loss often occur because air or fluid does not flow as expected. With CFD, we combine flow and heat transfer in a single analysis. This allows us to visualise where heat originates, how it is dissipated and which parts of a system are insufficiently or unnecessarily strongly cooled.

Typical problems

Typical problems

Typical problems

  • The temperature distribution is not uniform.

  • Parts or products become locally overheated.

  • A cooling system is not achieving the desired capacity.

  • Fans or pumps are running at high power without sufficient result.

  • Hot, poorly ventilated areas form behind components.

  • A product warms up or cools down more slowly than expected.

  • The outlet temperature deviates from the design specification.

  • It is not clear where heat losses are occurring.

  • Temperature measurements only provide information at a few points.

  • Adjustments to flow rate or cooling capacity yield little improvement.

What we investigate

What we investigate

What we investigate

  • The flow of cooling or heating media.

  • Temperature distribution in liquids, gases and solid components.

  • Heat transfer between flow and solid surfaces.

  • Convection, conduction and, where relevant, thermal radiation.

  • Hot and cold zones within the system.

  • Recirculation areas where heat remains trapped.

  • The influence of inlet temperature and volumetric flow rate.

  • The thermal load of individual components.

  • Warming or cooling over time.

  • The influence of material choice, insulation and wall thickness.

Potential improvements

Potential improvements

Potential improvements

  • Making the distribution across different channels more uniform.

  • Adjusting the position or direction of cooling and heating flows.

  • Reducing dead zones and hot recirculation areas.

  • Repositioning fans, pumps or sprayers.

  • Optimising cooling fins, guide vanes or internal components.

  • Adjusting the geometry of heat-exchanging surfaces.

  • Reducing unnecessary pressure losses in the cooling system.

  • Using insulation or materials more effectively.

  • Reducing the required cooling or heating capacity.

  • Comparing different design variants before realisation.

Applications

Applications

Applications

  • Electrical and electronic components.

  • Heat exchangers and coolers.

  • Batteries and energy storage systems.

  • Motors, machines and technical installations.

  • Ovens, dryers and heating systems.

  • Process vessels and reactors.

  • Cold stores and conditioned rooms.

  • Ventilation and air handling systems.

  • Product cooling and product heating.

  • Pipes, ducts and industrial enclosures.

Our approach

Our approach

Our approach

  1. We discuss the desired temperatures and the observed problems.

  2. We collect data on geometry, materials and operating conditions.

  3. We determine which heat sources, wall conditions and cooling flows are relevant.

  4. We build a CFD model of the flow and heat transfer.

  5. We analyse temperature fields, heat flows and local problem areas.

  6. We investigate the cause of overheating or insufficient cooling.

  7. We compare possible adjustments to geometry and operating conditions.

  8. We present the results in clear images and practical recommendations.

Why FlowMotion

Why FlowMotion

Why FlowMotion

  • More than 1,250 projects completed.

  • Over thirty years of experience with industrial flow and heat transfer.

  • Analysis of temperature and the underlying flow behaviour.

  • Technical results translated into practically implementable improvements.

  • Design variants can be compared independently in advance.

  • Clear visualisations of temperature fields that are difficult to measure.

  • Personal contact and direct consultation with an experienced CFD specialist.

Is your system or product running too hot?

Let us review the combination of flow, cooling and heat transfer. With CFD, we visualise where the problem originates and which adjustments can have the most effect.